Decide the form before you wet a single decal
The EVO Studio sheet for the RG 1/144 Gundam GP01+FB includes markings for both the GP01 and FB variations. That single fact should shape your whole session: choose which form you are finishing first, then treat the other form's markings as a separate later job. Trying to split one sheet across two builds at once invites confusion, misplaced markings, and wasted decals.
This guide focuses on placement planning and dry-fit checks for 1/144 scale work. The supplied product information confirms compatibility with RG 1/144 Gundam GP01+FB kits and describes the sheet as water-slide decals for clean application and a realistic appearance. It does not include a printed placement map, model-specific coordinates, or setting instructions, so the checkpoints below are about how to make decisions with the sheet in front of you, not a substitute for a manufacturer diagram.
What the EVO sheet confirms before you start
- RG 1/144 Gundam GP01+FB EVO Water Decal: Compatible with RG 1/144 Gundam GP01+FB model kits. This is the compatibility anchor. Confirm your kit is the RG 1/144 GP01+FB before planning any placement, because the sheet is not described as universal across other RG kits.

RG 1/144 Gundam GP01+FB EVO Water Decal - RG 1/144 Gundam GP01+FB EVO Water Decal: Includes markings for both GP01 and FB variations. You can plan two distinct finishing passes from one sheet, but you should decide which variation gets which markings before application rather than improvising mid-build.
- RG 1/144 Gundam GP01+FB EVO Water Decal: Water-slide decals for clean application and realistic appearance. The application method is water-slide, so your placement workflow should allow for sliding the decal into position and blotting it down, not pressing a dry sticker.
A placement-first workflow for the GP01 and FB forms
The order below keeps the two variations from competing for the same sheet space and gives you a chance to catch problems before a decal is committed.
- 1. Separate the two marking groups on the sheet: The sheet includes markings for both GP01 and FB variations. Before cutting anything, identify which markings you intend for the form you are building now. If the sheet does not label the groups clearly, make your own note or photo of the sheet layout so you do not borrow a marking meant for the other form.
- 2. Dry-fit each marking on the bare plastic: Hold or lightly position the uncut decal near its intended spot on the kit. At 1/144 scale, small markings can crowd panel lines, vents, and raised detail. The supplied information does not include a placement diagram, so this dry-fit is your main check that the marking sits where you expect.
- 3. Choose flat, accessible surfaces first: Start with markings that sit on broad, flat areas of the GP01 or FB form. Water-slide decals need to slide and settle, and flat surfaces give you the clearest view of whether the marking is straight. Save curved or detail-heavy areas for after you have built confidence with the sheet.
- 4. Apply one marking at a time and check alignment: Because these are water-slide decals, you can slide the film into position before blotting. Work one marking at a time so a misalignment does not force you to rush the next one. Keep the other form's markings untouched until you finish the current pass.
- 5. Finish the first form before starting the second: Once the GP01 or FB markings are placed and fully settled, move on to the other variation. This keeps the sheet organized and reduces the chance of mixing markings between forms.
Checkpoints that matter at 1/144 scale
These are practical checks you can make with the supplied sheet and your kit. They are not manufacturer instructions, and the product information does not specify drying times, setting solutions, or topcoat compatibility.
- Check the marking against the form: Before wetting a decal, confirm it belongs to the GP01 or FB variation you are currently finishing. The sheet includes markings for both, so a quick second look prevents cross-use.
- Check the surface for raised detail: At 1/144, a marking that crosses a raised edge or vent may not sit flat. Dry-fit first and reposition if the decal would bridge a gap.
- Check alignment from more than one angle: Water-slide decals can be nudged while wet. Look from the front and side before blotting so the marking reads straight on the finished model.
- Check that the decal has settled before moving on: The supplied information describes water-slide application but does not give a drying time. Give each marking enough time to settle before handling the part, and avoid stacking parts while decals are still wet.
Where the supplied information stops
The EVO sheet listing confirms compatibility, the two variation groups, and the water-slide method. It does not provide a printed placement guide, recommended setting solutions, drying times, topcoat advice, or a parts count. That means you should not expect the product page to answer questions like exactly which marking goes on which shoulder or how long to wait before clear coating.
Treat those gaps as decision points rather than defects. If you need a specific placement, use the kit's own instructions or your own dry-fit judgment. If you plan to topcoat over the decals, test on a spare marking first, because the supplied information does not confirm topcoat compatibility. The honest trade-off is that this sheet gives you markings for both forms and a water-slide method, but not a step-by-step map, so your own planning does the rest.


